Older Delta faucet repair

Older Delta Faucet Repair

  • by Jerry Miller

The unmarried most common faucet repair Abet Master Plumbing performs is the older Delta faucet repair. Our plumbers have had so many customers enquire them about it that I've decided to write a specific mail almost it. I've written nearly this in the past only not to the extent that I am now. I'll describe how this faucet repair is done past your local plumbers in Lees Summit. I'm going to begin with a video. Watch information technology start. And I'll and then give you the step by step diy faucet repair info.

Older single handle Delta faucet repair

I'm going to hash out the virtually common Delta single handle faucet design. It's important to recollect that the style doesn't mean much here. It's only the guts of the faucet that we'll exist worrying about. You'll find different designs and finishes for the same faucet. And I'm going to discuss the manner I do it. Faucet repairs are washed in various ways past professional plumbers.

older delta faucet repair
Delta RP3614 faucet repair kit

Tools and parts you'll need

  1. Delta faucet handle repair kit RP3614 & for kitchen faucets you'll too need RP63136
  2. Plumbers grease -Heat proof grease – Waterproof grease. All the aforementioned stuff.
  3. Mesh sand fabric
  4. Long handle pliers. Channel locks are ok. Wilde make are best.
  5. Multi-scrap screwdriver
    Delta RP63136 faucet repair kit
    Delta RP63136 faucet repair kit
  6. Hook and pick prepare
  7. Needle nose pliers

Step by step instructions

This is dry reading. But read the whole thing kickoff. So begin your projection. This is how nosotros repair faucets near yous.

  1. Close the h2o off. If you don't take faucet h2o shutoffs or you practice and they're scary looking, just close the h2o off to your whole house.
  2. Plug the sink bleed so no loose parts fall downwardly the drain.
  3. Remove the single handle. If you have a crystal handle you lot'll accept to pry the index button out of the middle of the handle with your screwdriver. Then remove the handle screw and so the handle. If you have a brass lever handle use the allen wrench end of the Delta faucet wrench that comes in your RP3614 repair kit to remove the allen spiral at the base of the handle and wiggle it off.
  4. Remove the bonnet nut. (The dome shaped cap.) You'll use your pliers for this. If the bonnet nut is seized, very mutual problem, use penetrating oil, CLR, WD40 or just a lot of elbow grease to remove it. If yous even so tin can't become it off I've gently sawed the cap at it's base and popped information technology open with a flat caput screwdriver. But it may exist easier to merely replace the faucet at this point.
  5. Remove the cam and packing and ball associates.
  6. Using the slightly angled pick remove the rubber seats and springs inside the base of operations of the faucet.
  7. If there are any hard water deposits use your sandcloth mesh to rubbed them off. Don't use a pick or screwdriver. You lot can mar the housing making it impossible to seal correctly.
  8. Lubricate the inside of the faucet housing and threads with your plumbers grease.
  9. Lubricate the new rubber seats in your handle repair kit. This will prevent cracking and allow for a ameliorate seal.
  10. Put the smaller cease of each conical spring within each rubber seat. Then put your straight pick through the top of the rubber seat and bound. Using the selection as a guide, place the finish of the selection inside each seat orifice inside the faucet and slide the seat and spring in place while pulling the selection out. You may need to piece of work it in place with your finger until it pops in identify.
  11. If the quondam ball assembly has a directly shaft then you'll exist using the triangular cam. If it has a triangular shaft you'll utilise the cam with the straight groove. Simply look at your former parts. If you're reusing your sometime ball assembly gently scrub any difficult water deposits off with your sandcloth mesh and lubricate it with your plumbers grease. Place the ball assembly into the housing being sure to match the groove in the side of the brawl assembly with the little nub on the interior housing of the faucet.
  12. Lubricate the cam and packing with your plumbers grease. Put them together and place them on elevation of the ball assembly. Exist sure to friction match up the nub on the exterior of the cam with the groove on the edge of the faucet housing.
  13. Put 1 finger through the bonnet nut and use the aforementioned finger to push and agree down the cam and packing while threading the bonnet nut on with your other hand. Effort it a couple of times. You'll get it.
  14. Reassemble handle. Plow the h2o back on. Test for leaks. If the cam and packing leaks at all apply the Delta wrench with the 2 prongs to thread the top of the cam clockwise a picayune.
Older Delta faucet repair
Delta kitchen faucet parts

Delta single handle kitchen faucet vegetable sprayer

If it's a kitchen faucet you're repairing y'all may discover that the vegetable sprayer isn't working correctly. It will frequently get jammed up with hard water or the the rubber seals will become stuck. For this repair we'll simply dive into the middle of the previous instructions.

Before beginning step 6 yous'll want to wiggle the whole kitchen spout off the faucet housing. You lot'll need to rotate it back and forth while pulling up. You'll run into two o-rings around the exterior of the faucet housing. Using your angled option remove them. Then you'll run across a round plastic stalk almost the base of operations of the front of the faucet housing. This is the diverter valve. I use needle nose pliers or my pick fix to remove the one-time 1. If in that location's any hard water deposits use your sandcloth mesh to remove them. Lubricate the opening with heat proof grease. Lubricate the new diverter valve (Delta RP63136 diverter valve) Printing the new valve into the faucet. Lubricate the ii large o-rings and install them in the advisable spots on the shaft. Clean and lubricate the inside of the faucet spout housing and slide it back onto the faucet housing. And then proceed to stride 6 above.

Older Delta Faucet Repair Well-nigh Yous

This sounds similar a lot. If you feel overwhelmed or just want a professional to handle it experience free to phone call Abet Chief Plumbing. We've been repairing older Delta faucets for over 27 years. We accept fair pricing and don't send salesmen into your home.